top of page

10 Different Ways to Roll a Joint

Updated: May 3


Title: 10 different ways to roll a joint

Rolling a joint is an art form that has been practiced for decades by cannabis enthusiasts around the world. While there is no one "correct" way to roll a joint, there are certainly many different techniques and styles that can produce a high-quality smoking experience. Here are 10 different ways to roll a joint:


1. Basic Joint Roll:

The most common way to roll a joint is by using the basic rolling technique. To do this, you'll need rolling papers, ground cannabis, and a filter. Start by creating a crutch, or filter, using a small piece of cardboard or paper. Next, place the crutch at one end of the rolling paper, add your cannabis, and roll the paper between your fingers, tucking the paper under the cannabis as you go. Finally, lick the adhesive strip on the paper, seal the joint, and twist the open end to close it.


2.Cone Joint Roll:

The cone joint roll is similar to the basic roll, but instead of rolling the paper evenly, you create a cone shape that allows for a larger amount of cannabis at the end. This is achieved by rolling the paper around the crutch and then gradually adding more cannabis as you go. This results in a tapered end that burns slowly and evenly.


3. Cross Joint Roll:

The cross joint is a bit of a novelty and requires some extra materials, but it's a fun way to impress your friends. To make a cross joint, you'll need two rolling papers, one filter, and a third piece of paper or a needle to create a hole. Start by rolling a basic joint, then roll a second joint that's slightly thicker. Poke a hole through the side of the thicker joint, insert the smaller joint into the hole, and seal the two joints together. This creates a "cross" shape, hence the name.


4. Tulip Joint Roll:

The tulip joint is a creative way to add some flair to your smoking experience. To create a tulip joint, you'll need a rolling paper, a filter, and a small amount of extra paper. Start by creating a basic joint, but instead of twisting the open end, fold it inward and use the extra paper to wrap around the top to create a tulip shape.


5. Inside-Out Joint Roll:

The inside-out joint, also known as a "backroll," is a great way to prevent any excess paper from burning and getting into your lungs. To make an inside-out joint, start by flipping the rolling paper so that the adhesive strip faces down. Then, place your crutch and cannabis on the paper, and roll it up. Finally, lick the adhesive strip and roll the joint again to seal it.


6. Shotgun Joint Roll:

The shotgun joint is a unique way to share a joint with a friend. To create a shotgun joint, roll a basic joint with a longer crutch. Then, poke a small hole through the center of the crutch with a pin or needle. Light the joint and place the crutch in your friend's mouth, and they can inhale the smoke through the hole in the crutch.


7. Blunt Roll:

A blunt is a type of joint that's made with a cigar wrap instead of rolling paper. To make a blunt, split the cigar wrap down the middle and remove the tobacco. Then, fill the wrap with your ground cannabis and roll it up. Blunts tend to burn slower and last longer than traditional joints.


8. Braided Joint Roll:

The braided joint is a creative way to add some visual interest to your smoking experience. To make a braided joint, start by rolling three separate joints, all with the same length and thickness. Then, place the three joints together and braid them together, much like you would with hair. Once the joints are braided, seal the ends together to create a single joint that can be smoked.


9. L-Shaped Joint Roll:

The L-shaped joint is a fun way to add some variety to your smoking experience. To make an L-shaped joint, roll a basic joint as you normally would. Then, create a second joint that's shorter and thicker. Attach the two joints together at a 90-degree angle to create an L-shape.


10. Paper Airplane Joint Roll:

The paper airplane joint is a novelty roll that's sure to impress your friends. To make a paper airplane joint, start by rolling a basic joint with a longer crutch. Then, fold the joint in half, tucking the open end into the crutch to create a wing-like shape. Finally, add some additional paper to the end of the joint to create a tail, and you have a joint that looks like a paper airplane.


We can roll for you if you need!



Comments


bottom of page